Air conditioning system installation process

Nowadays, the use of air-conditioning in buildings, offices, and constructions has become very popular. Most buildings during construction are equipped with air-conditioning systems because of its effectiveness and convenience in use. With air-conditioning, after installation is complete, users can use it simply by pressing the button in each mode. However, the improper installation of air conditioning systems often leads to unintended damage. Installing the air conditioner looks simple but requires a lot of technical factors: accuracy, meticulousness, care, ...

So how is the process of installing an air conditioning system?

Tan Hoang Phat Company would like to introduce to you how to install the air conditioner with correct technique:

Standard steps before proceeding with the installation

Air conditioning installation diagram

- Indoor unit installation location:

Sturdy and free from vibration when operating

Ensure aesthetics in the room

Located away from heat sources and hotter, not blocked by wind.

Condensed water can flow easily, power is guaranteed

- Installation location of outdoor unit:

Ensure good ventilation, wind, should avoid rain and direct sunlight

Solid installation position, ensuring aesthetics in the room, less vibration noise when operating.

The wind from the outdoor unit has little effect on the surrounding environment

There is no flammable air, leaking around the outdoor unit

The air from the outdoor unit is not obstructed.

Convenient installation location for air conditioner disassembly and maintenance when needed.

2.  Steps to install an air conditioning system: divided into 4 steps

Step 1: Install the indoor unit

 – The indoor unit is hung on the wall, about 5cm from the ceiling (with wall-mounted air conditioning). Remove the corrugated board installed in the back of the indoor unit. use corrugated iron panels and measure the installation dimensions, balancing corrugated iron board Go in, Adjust the corrugated iron board for balance and then take the mark. When taking the mark, conduct drilling and then screw the corrugated board to the wall.

 – Use a screwdriver to remove the outer cover of the indoor unit to connect the electrical wires and signal wires according to the instructions in the attached book.

 – Align copper pipes to suit the drill holes, remove the jacks, use tape to seal the two ends of the hole, to avoid dust ingress.

 – Wrap insulation, water pipes, copper pipe, wire in a block threaded through the hole drilled out.

 – Hang the cold side on the corrugated board just caught, use Nivo to re-align the indoor unit, This is also the last stage in the installation of an air-conditioning unit.

Step 2. Install the outdoor unit

– Position the outdoor unit is placed on a concrete or shelving with minimum height is 100mm were held together by bolts.

If the outdoor unit is mounted on a bracket, the following steps will be taken:
- Measure the location of the hanging bracket, take the mark.
- Use a drill, drill at the position just took the seal, close the hatch and then catch the price.
- Put the machine on the shelf, use bolts to fasten the tripod to the bracket
- Install the drain hose on the bottom of the outdoor unit (for 2-way machines).

Step 3. Step of connecting pipes

Usually use the pipe welding method. Requirements set is sealed weld absolute must. Check with specialized equipment.

Step 4: Conduct test, test run

After completing the above steps, the process will be checked and tested.

The air conditioner is considered to function well when it meets the following requirements:

– Conditioner operates stably for at least 30 minutes after test run

– The noise from the outdoor unit is completely eliminated

– Ensure technical standards when operating

Above are some basic information sharing to help you better understand the standard air conditioner installation process.

If your construction projects are in need of air-conditioning installation, please contact us to get the best finishing solution.

DIENCONGNGHIEP.TOP
    Quality pioneer
    Skilled technical team, professional
    Cost savings
    Rapid construction
    Labor safety assurance
    Provide 100% genuine products
Design and design verification
   - Factory design
   - Industrial buildings,
   - Design ventilation air conditioning system,
   - Mild electrical design,
   - Heavy electrical design,
   - Fire protection design.
   - Water supply and drainage design.
Construction
   - Construction of light electrical systems
   - Construction of fire protection system.
   - Factory design and construction
   - Design and Construction of electromechanical works
   - Electrical construction
   - Construction of the factory electromechanical system
   - Construction of M&E system
   - Installation of electromechanical systems
   - Construction of air conditioning system
   - Construction of ventilation system
   - Installation of HVAC system
   - Install cold cellar cold room
   - Design and installation of clean rooms
   - Construction of clean rooms
   - Factory design
   - Apply for a factory building permit
   - Fastest factory building design
   - Construction of water supply and drainage system
   - Construction of camera system
   - Construction of water supply and drainage system
Product distribution
   - Genuine distribution
   - Quality assurance
   - Full CO CQ
   - Long-term warranty works

CONTACT OFFICE
Tan Hoang Phat Design and Construction Investment Company Limited
Address: 5th Floor, Central Point 219 Trung Kinh, Yen Hoa Cau Giay, Hanoi City

 Website: http://diencongnghiep.top
 Email: diencongnghiep.top@gmail.com

Facebook: https://www.facebook.com/congtytanhoangphat
Hotline: 0911.066.518, 0969.002.382